NOCO GEN5X1
1 independent bank · 5A per bank
5A combined output · 12V battery charging
View exact charger and conditionNOCO GEN5X vs GENPRO10X Marine Chargers: Banks & Amps
When replacing an onboard marine battery charger, count the batteries that must be charged independently and then choose how much current each battery should receive. NOCO's GEN5X and GENPRO10X chargers use a similar waterproof design, but the GEN5X family provides 5 amps per bank while GENPRO10X provides 10 amps per bank. This guide helps identify seven exact models without confusing the total output with the rating of each charging connection.
GEN5X versus GENPRO10X
GEN5X: 5 amps per bankGEN5X1 has one 5A output, GEN5X2 has two 5A outputs for 10A total, and GEN5X3 has three 5A outputs for 15A total. Each charging bank operates separately so suitable batteries can be charged and maintained without sharing one set of battery terminals.
GENPRO10X: 10 amps per bankGENPRO10X1 supplies 10A to one battery, X2 supplies 20A total across two banks, X3 supplies 30A across three, and X4 supplies 40A across four. These models are intended for installations that need more current at each connection.
NOCO marine charger part-number chart
| NOCO model | Product family | Banks | Current per bank | Combined maximum |
|---|---|---|---|---|
| GEN5X1 | GEN5X | 1 | 5A | 5A |
| GEN5X2 | GEN5X | 2 | 5A | 10A |
| GEN5X3 | GEN5X | 3 | 5A | 15A |
| GENPRO10X1 | GENPRO10X | 1 | 10A | 10A |
| GENPRO10X2 | GENPRO10X | 2 | 10A | 20A |
| GENPRO10X3 | GENPRO10X | 3 | 10A | 30A |
| GENPRO10X4 | GENPRO10X | 4 | 10A | 40A |
Read the current ratings carefully: GEN5X3 is a 15A total charger with three independently controlled 5A outputs. GENPRO10X3 is a 30A total charger with three 10A outputs. Neither supplies its total rated current to every battery simultaneously.
Which batteries are supported?
NOCO provides independently selectable 12V lead-acid, AGM and compatible 12V lithium charging modes on these marine chargers. The batteries must meet the manufacturer's mode-specific chemistry, voltage and capacity requirements; lithium charging is intended for qualifying battery packs with an appropriate battery management system. Do not assume support for every lithium chemistry, 6V battery, or a single higher-voltage battery solely because the charger can maintain several separate 12V banks.
The chargers offer temperature-aware charging, automatic maintenance and recovery features. Certain recovery modes may deliberately bypass standard protections and should be used only according to the manual and the battery manufacturer's instructions.
Waterproof housing does not eliminate installation rules
NOCO specifies IP68 protection for the marine onboard ranges. Nevertheless, mounting, cable routing, battery ventilation, AC power, DC fuses and connection polarity still require the exact instructions for the chosen model. Use suitable marine electrical practices; do not place exposed connectors where they can be flooded or damaged by moving equipment.
Before replacing the existing charger
- Count the independent battery banks. Confirm the number of 12V batteries needing individually controlled outputs and compare the existing battery wiring to the charger's diagrams.
- Choose current per bank. Select 5A or 10A per output based on the batteries' approved charging rates and desired charging speed. Do not select solely by the charger's total amp headline.
- Verify battery chemistry. Check the battery's label, BMS requirements and the NOCO charging mode before making connections.
- Measure the mounting area. Compare the exact unit's physical dimensions, cable lengths, lead exits and clearance needs. Similar-looking X2 models can have different housings.
- Review AC input and circuit protection. Confirm a suitable AC supply, fuses, polarity and all specified installation hardware. Isolate shore power and batteries before changing a charger.
- Check charging operation. After installation, confirm each bank detects its intended battery and enters the correct charge or maintenance state. Seek a qualified marine electrician for uncertain wiring or a modified battery system.
Shop matching NOCO onboard marine chargers
These cards open exact UsedRVParts.ca products. Check the condition and live availability before ordering; this store sells new products alongside used RV and marine equipment. Eligible used inventory can be viewed or collected in Kelowna by appointment.
NOCO GEN5X2
2 independent banks · 5A per bank
10A combined output · 12V battery charging
View exact charger and condition
NOCO GEN5X3
3 independent banks · 5A per bank
15A combined output · 12V battery charging
View exact charger and condition
NOCO GENPRO10X1
1 independent bank · 10A per bank
10A combined output · 12V battery charging
View exact charger and condition
NOCO GENPRO10X2
2 independent banks · 10A per bank
20A combined output · 12V battery charging
View exact charger and condition
NOCO GENPRO10X3
3 independent banks · 10A per bank
30A combined output · 12V battery charging
View exact charger and condition
NOCO GENPRO10X4
4 independent banks · 10A per bank
40A combined output · 12V battery charging
View exact charger and conditionRelated battery wiring references
Before altering battery connections, our Blue Sea 11001 and 11003 selector switch guide explains a separate switching component. For fusing near battery posts, see the Blue Sea MRBF fuse-holder reference. Charger selection alone does not prove an entire circuit's safety or compatibility.
Recently viewed
New & Updated RV Parts Inventory — Check Back Often
We’re always adding new and used RV parts to our inventory, so be sure to check back regularly.
If you don’t see the part you need today, we may still have it in stock—our internal database includes thousands of new RV parts that are not yet listed online.
Text or email us with the product number or model, and we’ll check availability for you right away.
Our Products