Atwood RV water heater thermostats are not universal, even when the outside of two thermodisc parts looks almost identical. Different heater models use different control arrangements, and XT water heaters use a higher-temperature system with a separate tempering valve. Match the full water heater model, original part number and installed controls before ordering a thermostat.

Three thermostat applications to distinguish

Conventional electric water heater

Atwood 91447 is listed as a 140°F front-mount thermostat with high-limit control for matching single-element electric heater designs. 91447MC is a separately branded replacement for listed Atwood electric applications.

Conventional gas or gas/electric water heater

Dometic 91470 is a thermostat listed for selected Atwood heater configurations. Confirm its factory setpoint and the exact model's service-part reference before treating it as a match.

XT high-temperature water heater

91547 is the 180°F thermostat listed for selected Atwood XT designs. It belongs in a system using an approved hot-water mixing valve, not an ordinary water heater without that protection.

Temperature is part of the safety design: Do not install a higher-setpoint thermostat in an ordinary water heater to get hotter water. A misapplied thermostat or bypassed high-limit control can cause scalding and unsafe operation. Always use the exact manufacturer-approved component and service procedure.

Why XT water heaters are different

Original conceptual flow, not a piping installation diagram. A correctly configured mixing valve is required; do not bypass it. Check the heater's exact factory schematic and relief/limit safety devices.

Compare Atwood thermostat part numbers

Part number Thermostat type Temperature information Fitment check
91447 Electric heater thermostat 140°F listed setting Identify the precise electric-element thermostat installation and original part number.
91447MC Aftermarket electric thermostat 140°F listed setting Manufacturer suffix matters. Confirm that the replacement part is approved for the exact original appliance.
91470 Conventional gas-heater thermostat See model-specific service document Not identified as an XT 180°F thermostat. Check the heater model and control assembly.
91547 XT heater thermostat 180°F listed setting An XT heater uses a mixing-valve arrangement and is not made equivalent to an ordinary heater by exchanging thermostats.

Both 91447 and 91447MC have 140°F listed settings and high-limit features, but different branding does not by itself certify every installation as interchangeable. Likewise, the 91470 listing covers selected conventional heater arrangements, not a blanket fitment claim for every G6, GC6, or XT unit. Exact heater variants and service revisions matter.

Four checks before buying

  1. Record the water heater model. Read the complete model number and any suffix on the data plate.
  2. Identify gas, electric or XT operation. A heater with electric and propane modes may have separate controls; confirm which thermostat circuit is being serviced.
  3. Match the original thermostat and high-limit assembly. Check connector location, mounting format, manufacturer part number and documented setpoint.
  4. Follow the service instructions. Isolate electrical and propane energy sources and allow the heater to cool before service. A qualified technician should handle safety control testing and repairs.

Matching water-heater thermostat listings

Common questions

Can I replace a 91447 with a 91547 to make the water hotter?

No. The 91547 is specified for designated XT high-temperature heaters with the appropriate mixing-valve arrangement. A conventional system must use its approved thermostat and safety controls.

Are 91447 and 91447MC identical?

Both are sold for selected conventional Atwood electric-water-heater applications and carry 140°F listings, but the parts are from different manufacturers. Verify that the exact heater model supports the replacement.

Does the 91470 thermostat fit every Atwood gas/electric water heater?

No universal coverage is established. Check the precise heater model and the manufacturer's service parts list, including the correct temperature rating and control assembly.

What does the XT water heater mixing valve do?

It mixes hot tank water with the cold supply to deliver appropriately tempered water. A defective or bypassed valve creates a burn hazard and requires proper service rather than changing the thermostat setpoint.

Related Atwood water-heater reference diagrams

These references help identify the correct parts. Follow the appliance manufacturer's latest service specifications for thermostat limits, installation and commissioning.

Quick thermostat links: 91447 · 91447MC · 91470 · 91547

Recently viewed

New & Updated RV Parts Inventory — Check Back Often

We’re always adding new and used RV parts to our inventory, so be sure to check back regularly.

If you don’t see the part you need today, we may still have it in stock—our internal database includes thousands of new RV parts that are not yet listed online.

Text or email us with the product number or model, and we’ll check availability for you right away.

Our Products

RV Parts Newsletter

Sign up for upcoming promotions!