CC-100 — CC-100 hitch-mounted cargo platform
View CC-100 productStromberg CC-100 Cargo Caddy & CC-125 Bike Kit: Parts Diagram
The Stromberg Carlson CC-100 Cargo Caddy is a hitch-mounted steel cargo platform that fits a suitable 2-inch receiver. For bicycles, the separate CC-125 kit adds four wheel-support brackets and the retention hardware needed to convert the CC-100 into a two-bike carrier. This guide identifies the original parts of both assemblies so you can determine whether you need the platform, the conversion kit or a missing hardware component.
CC-100 and CC-125: which product do you need?
| Exact model | What it supplies | Manufacturer detail |
|---|---|---|
| CC-100 | Complete cargo tray assembly | Approximately 23 × 60-inch interior, expanded-metal deck and 2-inch receiver tube; rated up to 500 lb of evenly distributed cargo, subject to the vehicle and hitch limits |
| CC-125 | Two-bicycle conversion hardware | Four tire holders, eight carriage bolts, eight locknuts and two frame tie-down straps; intended for the CC-100 tray |
CC-100 numbered factory assembly components
Stromberg's assembly drawing numbers the five structural groups and separates the included fasteners by length. The two platform halves join before the receiver tube and supporting braces are attached.
| Drawing number | Factory component | Quantity in CC-100 |
|---|---|---|
| 1 | Expanded-metal platform half | 2 |
| 2 | Four-hole joining plate | 2 |
| 3 | 2-inch receiver bar | 1 |
| 4 | Channel brace | 2 |
| 5 | Support bridge | 2 |
11 + 2: tray platform
Two mesh platform halves are joined using the four-hole plates and short carriage bolts.
23 + 5: receiver support
The 2-inch receiver bar and two support bridges connect beneath the platform.
34: side braces
Channel braces tie the tray edges to the support structure.
4Receiver hitch
The completed carrier slides into a properly rated vehicle-mounted hitch and is secured with a suitable hitch pin.
Simplified component map. The factory PDF includes the actual exploded illustration and Figures A–C for fastener placement.
Hardware supplied for the complete CC-100 tray
| Factory hardware | Quantity |
|---|---|
| Short carriage bolts | 8 |
| Medium carriage bolts | 4 |
| Long carriage bolts | 3 |
| Locknuts | 15 |
The manufacturer's original instructions explicitly say the vehicle receiver hitch and the clevis/hitch pin are not included with the CC-100. Confirm you have appropriate retention hardware before using the cargo tray.
CC-125 two-bike conversion kit contents
| CC-125 component | Quantity | Function |
|---|---|---|
| Wheel/tire holders | 4 | Support the front and rear tire of each bicycle on the cargo tray |
| Carriage bolts | 8 | Secure the wheel holders through the CC-100 mesh platform |
| Locknuts | 8 | Retain the wheel-holder fasteners |
| Tie-down straps | 2 | Secure bicycle frames to the outer cargo-tray frame |
Place the holders around the actual wheelbase of each bike, with holders positioned against the inside of the tires. The manufacturer's instructions require straps to attach to the outer frame, not the expanded-metal deck; attaching straps to the mesh can lead to failure. The CC-125 accepts tires up to 2¼ inches wide, with the wheel cradles standing approximately 11½ inches above the tray surface.
View CC-100 productCC-125 — CC-125 two-bicycle wheel-holder kit
View CC-125 productFit and carrying limits
- Confirm the vehicle has a properly rated 2-inch receiver and adequate rear clearance for the full tray and any bicycles.
- Use the lower of the vehicle, receiver and carrier weight limits. Include the carrier's own weight when calculating load on the hitch; the CC-100 manufacturer lists the carrier at approximately 40 lb.
- Distribute cargo evenly and secure it so it cannot shift, obscure lights or contact hot exhaust components.
- For bicycles, confirm tire width and actual weight, use the CC-125 holders and frame straps as instructed, and check vehicle clearances before travel.
- Stromberg states the CC-100/CC-125 arrangement is not approved for e-bikes or motorbikes.
Original diagrams and instructions
CC-100 parts drawing and Figures A–C (PDF); CC-125 wheel-holder and tie-down instructions (PDF); CC-100 cargo platform specifications; CC-125 wheel-holder specifications. See the 2026 catalog, printed page 25 for the factory size references.
For a bicycle carrier fitted to an A-frame-mounted receiver rather than a rear cargo tray, see the CC-275 Bike Bunk reference guide; it uses a different mounting structure and has a different rating.
Recently viewed
New & Updated RV Parts Inventory — Check Back Often
We’re always adding new and used RV parts to our inventory, so be sure to check back regularly.
If you don’t see the part you need today, we may still have it in stock—our internal database includes thousands of new RV parts that are not yet listed online.
Text or email us with the product number or model, and we’ll check availability for you right away.
Our Products