Lippert JT’s Strong Arm stabilizers use bracing between an RV frame and its landing gear or stabilizer jacks. If the brace will not tighten, a frame-end bolt is damaged or its mounting point does not fit a round hydraulic footpad, the repair parts are different. This guide helps identify 314592 adapter lugs, 314594 tightening T-bolts and 314596 swing bolts without confusing them with a complete stabilizer system.

Choose the component by its job

314592 · Footpad adapter lugs

Used when attaching JT’s Strong Arm braces to compatible round hydraulic landing-gear footpads. The factory kit contains two lugs, not a pair of complete stabilizer bars.

Find adapter lugs

314594 · Tightening T-bolts

Lock the telescoping stabilizer braces in the proper position. The manufacturer lists two T-bolts per kit.

Find tightening bolts

314596 · Four-inch swing bolts

These mount a brace at a compatible frame-end bracket connection. Factory kit contents are two 4-inch swing bolts, four washers and two nuts.

Find swing-bolt kit

How the three pieces relate to the stabilizer

Original functional illustration, not a scaled installation drawing. The 314592 adapter is only applicable to the corresponding round hydraulic footpad connection; other jack mounting styles use different brackets.

Important operating instruction: Lippert specifies that the 314594 T-bolts must always be loosened before extending or retracting the stabilizer jacks. Tightening them during movement can damage braces, jacks or mounting components. These stabilizers reduce movement at the campsite; they are not a substitute for the RV's rated lifting or leveling system.

Compare exact Lippert JT’s Strong Arm repair numbers

Manufacturer number Where it works What the kit contains / does
314592 Round hydraulic landing-gear footpads Two adapter lugs that provide an attachment point between suitable round hydraulic jack footpads and JT’s Strong Arm stabilizer braces.
314594 Telescoping stabilizer brace lock Two T-bolts used to tighten the stabilizer brace in its set position for camping and secure it during travel.
314596 Brace-to-frame bracket joint Four-inch swing-bolt kit with two bolts, four washers and two nuts for the matching JT’s Strong Arm joint.

Do not confuse the two swing-bolt lengths

Lippert lists 314596 as its 4-inch swing-bolt kit and 314595 as a separate 1-1/4-inch swing-bolt kit. Both are genuine JT’s Strong Arm service components, but their length and installation positions are different. The product cards below link to the 4-inch kit currently listed here; identify the existing bolt and bracket before ordering.

Replacement checklist

  1. Confirm the stabilizer system. Verify that the installed brace is a Lippert JT’s Strong Arm, and identify the brace and jack configurations.
  2. Locate the damaged connection. Frame swing bolt, telescoping brace locking bolt, and hydraulic-footpad adapter lugs serve different jobs.
  3. Check dimensions and package quantity. Use the correct swing-bolt length and the manufacturer-listed washers, nuts or adapter lugs. Don't substitute general-purpose hardware of unknown grade.
  4. Follow the current Lippert instructions. Keep the RV correctly supported with its normal landing gear or jacks, and do not use a stabilizer brace to lift the trailer.

Shop matching JT’s Strong Arm repair components

Frequently asked questions

Is 314592 an entire stabilizer jack?

No. It is an adapter lug kit for attaching a suitable JT’s Strong Arm brace to a compatible round hydraulic landing-gear footpad.

How many T-bolts come in 314594?

Lippert's replacement parts catalog lists two tightening T-bolts. Check the individual product listing for fulfillment details.

Are 314595 and 314596 the same swing-bolt kit?

No. Lippert identifies them as 1-1/4-inch and 4-inch versions respectively. Match the existing bracket and bolt length.

Should the T-bolts stay tightened when I raise the jacks?

No. Lippert directs owners to loosen T-bolts before raising or lowering stabilizer jacks, then retighten for the appropriate camping or travel configuration.

Can I view these parts at the UsedRVParts location?

Viewing and pickup of eligible locally held items are by appointment in Kelowna. Verify the specific listing and arrange a time before visiting.

Related leveling and stabilizer reference pages

Manufacturer source: Lippert JT’s Strong Arm replacement part catalog. The exact installed kit and bracket determine which repair part is appropriate.

Quick part links: 314592 · 314594 · 314596

Récemment consulté

Inventaire de pièces détachées pour VR, nouveau et mis à jour – Consultez-le régulièrement

Nous ajoutons constamment des pièces neuves et d'occasion pour véhicules récréatifs à notre inventaire, alors assurez-vous de consulter régulièrement notre site.

Si vous ne trouvez pas la pièce dont vous avez besoin aujourd'hui, nous l'avons peut-être encore en stock : notre base de données interne comprend des milliers de pièces neuves pour véhicules de loisirs qui ne sont pas encore répertoriées en ligne.

Envoyez-nous un SMS ou un e-mail avec le numéro de produit ou le modèle , et nous vérifierons immédiatement sa disponibilité pour vous.

Nos produits

Bulletin d'information sur les pièces de camping-car

Inscrivez-vous pour les promotions à venir !