236575 — 300:1 in-wall slide-out motor
Manufacturer 300:1 drive motor. Match the current versus obsolete form and controller pairing; do not treat 229466 as a drop-in substitute.
Lippert Schwintek In-Wall Slide-Out Parts Diagram & Motor Guide
Identify the right replacement components for a Lippert Schwintek In-Wall slide-out. The in-wall design uses powered drive columns, upper and lower gear racks, motor harnesses and a synchronization controller; similar-looking systems can have different motor ratios and drive parts. Compare the original motor label, gear ratio and controller before selecting replacement parts.
Schwintek replacement parts: photos and part numbers
Compare the numbered motor, controller and bearing-block photos with your installed Schwintek system. Check the original gear ratio, label and wiring connectors.
How to identify the correct in-wall slide-out part
Before purchasing a motor or controller, record the full motor label, gear ratio, controller model and revision, and any H-column or slide variant code. Confirm the manufacturer-required motor/controller pairing. The early 229466 motor must not automatically be replaced with 236575, and the 287298 motor is a different high-torque 500:1 version. Parts that fit physically may still have incompatible drive ratios or electronics.
Schwintek replacement motors, controllers and bearing parts
287298 — 500:1 high-torque slide-out motor
Different motor gear ratio from 236575. Use only where the correct Lippert system specifies 500:1.
211852 — V-Sync II slide controller
Two-motor synchronization controller; compare the existing controller label, revision and system requirements.
238991 — 25-foot controller-to-motor harness
One specific harness length in a family of 5–35 ft cables. Confirm routed length and connector style.
379060 — Standard upper/lower bearing block kit
Manufacturer replacement bearing kit includes upper and lower blocks plus fasteners. Not a complete slide rail or column.
320500 — J-38 slide support roller
Under-room service roller. Verify roller geometry and location; not the V-roller inside the rack-drive column.
Other Schwintek drive and bearing components
229466 — older 300:1 motor (not a presumed substitute for 236575). 326876 — 8-amp controller, which Lippert says will not replace other controller versions.
238893 — standard spur gear; 292435 — copper-infused spur gear; 285085 — hex spur gear; 292801 — column V-roller assembly. These are different configurations.
238462 — aluminum shaft; 259065 — steel shaft; 295873 — hex shaft; 238461 — motor-shaft coupler (old/new designs). Match the original geometry.
Compare these part numbers with the gear-rack, shaft and motor-coupler versions installed on your slide-out.
Manufacturer service illustrations and repair cautions
Review the Lippert In-Wall Slide-Out technical document library for motor/controller compatibility, drive-column variants, rack identification, repair kits and troubleshooting. The Lippert In-Wall slide-out owner's manual (PDF) includes component drawings and dated manufacturer part-number lists; confirm revisions before ordering.
Safety: A slide room is heavy and can move unexpectedly. Do not loosen structural drive assemblies, disconnect motor restraint hardware or work under an unsupported room. Follow the manufacturer's service procedures or use a qualified RV technician for structural and electrical repairs.
Visto recientemente
Inventario de piezas para vehículos recreativos nuevo y actualizado: consulte con frecuencia
Siempre estamos agregando piezas de RV nuevas y usadas a nuestro inventario, así que asegúrese de volver a consultarlo periódicamente.
Si no ve la pieza que necesita hoy, es posible que aún la tengamos en stock: nuestra base de datos interna incluye miles de piezas de vehículos recreativos nuevas que aún no están publicadas en línea.
Envíenos un mensaje de texto o correo electrónico con el número de producto o modelo y verificaremos la disponibilidad de inmediato.
Nuestros productos