Lippert 2 x 2 Electric Through-Frame Slide-Out Parts Diagram

This guide is for Lippert 2×2-inch electric through-frame RV slide-out systems. The 2×2 rail and rack-drive mechanism is not the same as the larger 2.5×2.5 or Schwintek in-wall system. Identify the rail size and drive style before ordering an actuator, gear pack or drive shaft.

Factory exploded diagrams and component lists

Lippert factory 2 x 2 through-frame gear pack component drawing with callouts A through G
Lippert 2×2 gear-pack components, factory drawing CCD-0002560. Match the callout letters to the original parts list.
Lippert factory 2 x 2 electric through-frame center-drive slide-out assembly with labeled arms, motor and gear pack
Lippert 2×2 center-drive assembly. The actuator version uses a different drive layout.

For the true shape, location and order of assembly components, open Lippert's official 2×2 through-frame technical library. It includes separate 2×2 electric slide-out component references. See the manufacturer's current electric through-frame owner manual and electric through-frame service manual for operating and safety requirements.

Use the layout below to identify the drive, rails, gear pack and electrical components. Confirm the replacement against Lippert's model-specific parts drawing.

Where the main 2 × 2 slide-out parts fit

Drive assembly

Electric drive or actuator motor and matching gearbox. Identify original gearing, voltage and actuator length.

2×2 rails and rack

Inboard/outboard telescoping arms, rack teeth, drive shaft and 2×2-specific gear pack.

Stops and wear surfaces

Wear tabs, pads, rollers or stop hardware depend on the actual arm generation.

Electrical controls

In/out switch, motor wiring and electrical protection. Identify the existing switch before buying.

Check these two parts before ordering

Lippert lists 281331 as a 15-tooth gear-pack assembly supplied without roll pins. Earlier slide-out versions may use an 18-tooth gear, so compare the existing gear before ordering. Part 296090 is an outboard inner tube assembly with gear rack, not a drive shaft; the current replacement does not include a roller. Check the original rail, tooth arrangement and mounting before replacing it.

Manufacturer parts drawing: exact callout guide

The factory 2×2 electric through-frame illustrated list is in Lippert CCD-0001613: printed page 12 shows 2×2 gear-pack callouts A–G, page 15 shows tube assemblies V–Y (including 296090 at X), page 18 covers Venture drives, and page 20 shows cross-shafts. Choose the drawing for the original 2×2 rail and drive configuration before selecting a replacement.

Replacement slide-out components

Gear pack reference

281331 — 2×2 slide-out 15-tooth gear pack

281331 2×2 slide-out 15-tooth gear pack product photograph

Lippert 15-tooth gear-pack assembly for the matching 2×2 through-frame system. Roll pins are not included. Check the original rack geometry and tooth count.

Identify this as the complete 281331 gear-pack assembly, not just a loose spur gear.

Inner-tube reference

296090 — 2×2 outboard inner tube, 15-tooth

Lippert's replacement 296090 is a 72-inch, 2 × 2-inch outboard inner tube with gear rack; a roller is not included. Check the tube dimensions and mounting arrangement before replacement.

Check the original part number before ordering.

Actuator reference

132682 — 18:1 Venture motor

132682 18:1 Venture motor product photograph

Motor for the specified 18:1 actuator generation. Do not swap with 28:1 versions based only on connector or housing.

View matching product listing

Controls reference

117461 — White slide-out switch kit

117461 White slide-out switch kit product photograph

Match controller and motor wiring before selection. A switch listing is not proof of compatibility with every system.

View matching product listing

Gear pack reference

014-281331 — AP Products 15-tooth gear pack without roll pins

014-281331 AP Products 15-tooth gear pack without roll pins product photograph

A separately packaged branded 2×2 15-tooth option. Check pin requirements and gearbox/rack application.

View matching product listing

Do not mix sizes or gear families

A 2×2 gear pack is not interchangeable with standard 2.5×2.5 324869 or heavy-duty 2.5×2.5 123356 based merely on tooth count. The rack pitch and pressure-angle specification must match the actual system. Check the original Lippert identification label, rail dimensions, actuator gear ratio, serial number and factory part drawing.

For the larger mechanism, see the 2.5×2.5 through-frame slide-out reference.

Service precautions

Slide rooms are heavy, and rack/gear assemblies present pinch hazards. Disconnect the power supply and support the room in accordance with the manufacturer's procedure. Do not release a loaded actuator or work underneath an unsupported slide room. The information here is for identification, not a structural repair procedure.

Visto recientemente

Inventario de piezas para vehículos recreativos nuevo y actualizado: consulte con frecuencia

Siempre estamos agregando piezas de RV nuevas y usadas a nuestro inventario, así que asegúrese de volver a consultarlo periódicamente.

Si no ve la pieza que necesita hoy, es posible que aún la tengamos en stock: nuestra base de datos interna incluye miles de piezas de vehículos recreativos nuevas que aún no están publicadas en línea.

Envíenos un mensaje de texto o correo electrónico con el número de producto o modelo y verificaremos la disponibilidad de inmediato.

Nuestros productos

Enlaces rápidos populares

Frigoríficos usadosPiezas nuevas para refrigeradoresHornos usadosNuevos calentadores de aguaHornos y encimeras nuevosAire AcondicionadoToldos y repuestos nuevosPuertas y ventanas nuevasEnganches y Cajas de AcopleCamper sobre camionetaAccesorios para camionetasMarina

Boletín informativo de piezas para vehículos recreativos

¡Regístrate para próximas promociones!